Two Car Garage Epoxy in Meridian, Idaho

Meridian Quality Epoxy Floors coats two car garage epoxy stalls in Meridian. This is the production size in south Meridian, Star, and Kuna. The slab is usually 400 to 500 square feet of broom finish with builder joints, a water-heater pad, and sometimes a drain. The system is still grind, repair, coat.

Call (208) 502-8405 with a photo that shows both stalls. We measure. We do not bid a two-car job off a one-car kit price.

Two Car Garage Epoxy Options for Meridian Properties

Stall layout and builder details change the edge work more than the chemistry.

Twenty-by-twenty production two-car bays

The short production stall. Tight to the drywall. The water heater often sits on a pad in a back corner. We grind under the pad edge if the pad is staying. Flake is the usual look. Cars sit closer to the walls, so the perimeter coat has to be real, not a skipped stripe.

Twenty-four-by-twenty-four two car garage epoxy layouts

A 24-by-24 is about 576 square feet, above the 500 square foot mark Angi uses in its two-car table. Extra length is extra squeegee passes and extra chip. Tandem parking in a deep stall still counts as this job. A third door on the side is still this page until the footprint is a shop.

Builder joint and drain details

Saw cuts land where the builder put them, not where a coating drawing would want them. We fill those cuts so the coat does not bridge and split. A center drain needs a pitch that we do not fight. We coat into the drain ring. We do not bury a drain under flake.

Water-heater pad and stoop edges

The pad and the house stoop are the edges people see. We mask the heater, grind the pad, and terminate clean at the stoop. A thick puddle at the door becomes a trip. A starved edge at the pad peels first. Production houses in Cadence and Sky Mesa all have some version of this detail.

How We Handle Two Car Garage Epoxy Jobs in Meridian

1. We measure both stalls, the pad, and the door openings. Photos from the street are not a takeoff.
2. Everything comes out. We grind the whole slab, including the tire lanes and the walls.
3. Joints, the pad, and any spalls get filled. Primer and body go down as one field.
4. Flake or the system you picked is applied, then the wear coat. Both cars stay out until the window on the quote.

Materials and Methods

A two-car stall is still 100% solids epoxy on a CSP-3 grind. Vinyl chip to rejection is the common broadcast. Control-joint filler stays flexible. The water-heater pad is treated as floor, not as an island we skip. Drain rings are metal or plastic and get a termination, not a bury. Notched squeegees keep mils even across 400 to 500 square feet so the front stall does not starve while the back puddles. Spike shoes cross the wet field once. Masking at two overhead doors takes more tape than a one-car. Polyaspartic lock coats are common when both cars have to return on a weekday. This is a size page. The chemistry is the same family as the main garage system, with edges that only show up at this footprint.

What Two Car Garage Epoxy Costs in Meridian

Angi lists a two-car garage at 500 square feet for $1,500 to $6,000. HomeAdvisor uses the same two-car band. Fixr publishes $5,750-$8,625 as a high two-car installed figure, useful as a ceiling, not a bid. Three local movers: actual square footage after we measure, how much pad and joint work we find, and flake versus a faster polyaspartic lock. We quote the stall you have. We do not sell a two-car package from a flyer.

HOA packets in Paramount, Bridgetower, and Tuscany almost never name a floor system. They notice gloss at an open door and they notice a messy edge at the sidewalk. We mask to the slab edge and we keep grind dust out of the driveway. If your packet has a rule we should know, send a photo of that page. Most two-car bids do not wait on a design-review board.

Two Car Garage Epoxy Questions

How many square feet is a two car garage epoxy job?

Most Meridian production stalls run 400 to 500 square feet. A 20-by-20 is the short end. A 24-by-24 is common. We measure. Builder drawings are often short of the walls and the pad.

Do I need to empty the whole two-car bay?

Yes. Grinders need the floor. Cabinets, freezers, and the lawn mower have to come out. If a wall of cabinets is staying, say so. We coat around a bolted-down item only when you accept that edge.

Can you coat while we still park one car in the other stall?

Not during the grind and the coat. Split jobs exist when the stall is truly divided. Most production two-car bays are one slab. Plan on both cars out for the window on the quote.

How do I get a two car garage epoxy estimate in Meridian?

Call with the town and a photo that shows both stalls and the overhead doors. We quote after we measure. Angi and HomeAdvisor both list two-car bands you can read before we visit.

Call (208) 502-8405 with a photo of both stalls. We measure the slab you park on, not a typical two-car drawing.